Alltrax Controller Pro Software
| HPD (ON-OFF) High Pedal Disable |
AXE and DCX Models Only - Prevent motor controller from providing power if throttle is applied prior to Key Switch Turned on |
| PLUG BRAKE (ON-OFF) |
AXE "P" models ONLY with A2 terminal lug. Provides Plug Braking proportional to throttle position reaching full "Plugging" (Dynamic Motor Braking) when throttle below 25%. |
| TURBO (ON-OFF) | Provides higher speed when not in current limit and throttle is at 100% |
| 1/2 SPEED REVERSE | AXE and DCX Models Only - Limits vehicle speed in reverse based on 50% of forward "Top Speed" setting. |
|
MAX OUTPUT |
50-100% adjustment limits max current supplied to motor. Used to limit power. (The 400A controller set to 50%=200Amp max) |
| UNDER-VOLTAGE | Sets the under-voltage where the unit limits power and eventually shuts off and prevents battery damage. |
| OVER-VOLTAGE | Sets the over-voltage shutoff for the controller during excessive regen or overcharging to prevent damage. |
| THROTTLE UP RATE (1-15, Default 4) |
Determines the rate of controller output power based on an increasing throttle input. Setting 1=slow, 15=Fast. |
| THROTTLE DOWN RATE (1-15 Default 4) |
Determines the rate of controller output power based on a decreasing throttle input. Setting 1=slow, 15=Fast |
| BRAKE CURRENT (0-100%) |
AXE "P" Models - Adjusts the amount of Plug Brake Current as a percentage of 100A of brake current. DCX Models - Regeneration Feature is a percentage of possible current available. |
| TOP SPEED | Sets the top speed as a percentage of top-speed |
Features :
- Converts a standard 9-pin serial port to USB
- Complies with USB Specification v1.1(0) & USB CDC v1.1
- Full Compliance with USB specification v1.1
- Supports the RS 232 Serial interface (standard 9-pin serial)
- Supports automatic handshake mode
- USB full speed communication and Bus Powered
- Single Cable USB to Serial communication
- Supports up to 1 Mbps data transfer rate
- Supports Automatic handshake mode
- 6 Ft. Length
- Provides a 96 byte buffer for each upstream and downstream data transfer
- Drivers and Manual on a CD
- Easy Installation
For PC Users
- Windows® 95/98/98SE, 2000, ME, XP, Vista & 7
- Available USB port
Retail Package Content :
- USB to serial adapter cable
- Installation & Drivers on CD
LED Blink Codes:
At power up the number of green blinks indicates the configured throttle type:
1 Green = 0-5k
2 Green = 5k-0
3 Green = 0-5V
4 Green = EZ-GO inductive (ITS)
5 Green = Yamaha 0-1K
6 Green = Taylor-Dunn 6-10.5V
7 Green = CLUBCAR 5K-0, 3-wire
2 Green = 5k-0
3 Green = 0-5V
4 Green = EZ-GO inductive (ITS)
5 Green = Yamaha 0-1K
6 Green = Taylor-Dunn 6-10.5V
7 Green = CLUBCAR 5K-0, 3-wire
Normal display status:
Solid Green: Controller ready to run
Solid Red: Controller in programming mode
Solid Yellow: Controller throttle is wide open, controller is supplying max output, and is not in current limit.
Solid Red: Controller in programming mode
Solid Yellow: Controller throttle is wide open, controller is supplying max output, and is not in current limit.
Error code display:
Number of RED blinks indicates any error conditions that might exist.
1 Red = Throttle Position Sensor Over Range. Check for open wires.
2 Red = Under Temperature. Controller below -25C.
3 Red = HPD. Throttle hasn't gone to zero during this power on cycle.
4 Red = Over Temperature. Controller over 95C.
5 Red = unused for series controllers.
6 Red = Battery Under Voltage detected. Battery V < undervoltage slider.
7 Red = Battery Over Voltage detected. Battery V > overvoltage slider.
2 Red = Under Temperature. Controller below -25C.
3 Red = HPD. Throttle hasn't gone to zero during this power on cycle.
4 Red = Over Temperature. Controller over 95C.
5 Red = unused for series controllers.
6 Red = Battery Under Voltage detected. Battery V < undervoltage slider.
7 Red = Battery Over Voltage detected. Battery V > overvoltage slider.
